Launch control for 506 bin. WORKING
Moderators: robertisaar, dex
Launch control for 506 bin. WORKING
I got launch control / 2 step rev limiter working for the 506 bin.
It will be easy to change the rpm settings and to enable or disable in Tunerpro. I just need to finish up a 506 xdf file for N/A cars. It will be for the 506 chip #965.
I will send out the xdf and a stock bin modified with the launch control.
Anyone that wants it pm me your email and I will send it as soon as I am finished with the xdf. I will also make sure it gets posted in the download section
It will be easy to change the rpm settings and to enable or disable in Tunerpro. I just need to finish up a 506 xdf file for N/A cars. It will be for the 506 chip #965.
I will send out the xdf and a stock bin modified with the launch control.
Anyone that wants it pm me your email and I will send it as soon as I am finished with the xdf. I will also make sure it gets posted in the download section
The 506 xdf file is finished. It has working launch control, the load and rpm axis are auto correcting so if you open up a bin that had any of the rpm break points changed it will auto correct in Tunerpro for correct break point viewing. I also corrected any tables that are load based like the VANOS min & max.
Email me your address if you need a copy
Email me your address if you need a copy
-
- Posts: 1
- Joined: Thu May 28, 2015 9:57 pm
I set up launch control, probably around the same time you were working on this. My car was hit shortly after and a ditched the project. I used a little different trick though.
Change the map header to D7, coolant temp. Then set the break point scale for the rev limiter map to a reaonable set of temps except the final value; set it to something you shouldn't ever hit but wouldn't throw off your fueling if you did... say 250°F.
Wire up an SPDT relay as shown here https://lh5.googleusercontent.com/-vk7P ... launch.jpg
Push button, receive launch control (and possibly flat shift). I never tried altering the engine temp timing correction to pull timing and engine temp enrichment to add fuel... not sure how it would work with the fuel cut but if all goes to plan you'd have antilag on a factory DME.
Now if someone could just tell me how to shut off the VSS to kill the VSS fault rev limiter on my track car.
Change the map header to D7, coolant temp. Then set the break point scale for the rev limiter map to a reaonable set of temps except the final value; set it to something you shouldn't ever hit but wouldn't throw off your fueling if you did... say 250°F.
Wire up an SPDT relay as shown here https://lh5.googleusercontent.com/-vk7P ... launch.jpg
Push button, receive launch control (and possibly flat shift). I never tried altering the engine temp timing correction to pull timing and engine temp enrichment to add fuel... not sure how it would work with the fuel cut but if all goes to plan you'd have antilag on a factory DME.
Now if someone could just tell me how to shut off the VSS to kill the VSS fault rev limiter on my track car.
Re: Launch control for 506 bin. WORKING
My email: tason423@gmail.comevilm3666 wrote:I got launch control / 2 step rev limiter working for the 506 bin.
It will be easy to change the rpm settings and to enable or disable in Tunerpro. I just need to finish up a 506 xdf file for N/A cars. It will be for the 506 chip #965.
I will send out the xdf and a stock bin modified with the launch control.
Anyone that wants it pm me your email and I will send it as soon as I am finished with the xdf. I will also make sure it gets posted in the download section
-
- Posts: 28
- Joined: Fri May 06, 2011 7:11 am
-
- Posts: 28
- Joined: Fri May 06, 2011 7:11 am
Thanks you so much.Brian Shor wrote:Tason423,
I sent BIN to your email. S50B30US stock, 29lb/hr injectors, Garret 0.50front 0.63back, 90 octane AKI, 10psi boost, 3" AFM, 344whp, 365ft/lb.
This is a safe hp to start with, going over 400hp I would advise upgraded rod & pistons
You can use EvilM3666's xdf (506chip965) it works for 413
-
- Posts: 1
- Joined: Fri Nov 26, 2021 3:43 pm
Re: Launch control for 506 bin. WORKING
agronrama2002@gmail.com can u send it, 506 and 413. Please.
-
- Posts: 3
- Joined: Sun Sep 18, 2022 12:19 pm
Re: Launch control for 506 bin. WORKING
I PMd you my email!
Re: Launch control for 506 bin. WORKING
please share this file with me here is my email
antosevkolia@gmail.com
antosevkolia@gmail.com