V5 Wide Band Addition
Moderators: Mangus, robertisaar, dex
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
V5 Wide Band Addition
I have a Innovative Motor Sports LC-1 Wide band controller. I have it wired correctly and set it up in T.P. RT V4 like it shows. Now that I have updated to V5 it is not displaying the correct AFR on my dash. Does anyone know how it should be set up in the Definition files in V5? Also I have it connected through my Auto Prom.
Thanks,
Thanks,
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
I have been chatting with Robert and sent him my ADX file and he said he may have found out what it was and fixed it. I got it back and have yet to update it.
My truck just got sick. It keeps stalling when not under load in D or R. So I am trying to fix that before I went any further. But it won't take much to update the file and check it. So I will see about doing that tomorrow after work and update this thread.
My truck just got sick. It keeps stalling when not under load in D or R. So I am trying to fix that before I went any further. But it won't take much to update the file and check it. So I will see about doing that tomorrow after work and update this thread.
-
- Author of Defs
- Posts: 962
- Joined: Sat Feb 21, 2009 3:18 pm
- Location: Camden, MI
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
it's not clear in the manual... not referring directly to tunerproRally Smith wrote:http://www.innovatemotorsports.com/supp ... Manual.pdf
Power On The Road Equipped
...I always do by myself...
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
This may help too.
http://forum.tunerpro.net/viewtopic.php ... ht=scaling
http://forum.tunerpro.net/viewtopic.php ... ht=scaling
-
- Posts: 86
- Joined: Fri Aug 21, 2009 7:54 pm
O.k. sorry I haven't gotten back in a bit.
I looked at the file you sent to me Scott and mine is the same.
I read the info on the link that JP86SS provided and that make some sense to me.
However, I don't know where I need to go to make those changes for the wide band. "1024 and voltage/counts". This may be the ticket. Just a little more guidance on where to make the changes please.
Thanks,
R.S.
I looked at the file you sent to me Scott and mine is the same.
I read the info on the link that JP86SS provided and that make some sense to me.
However, I don't know where I need to go to make those changes for the wide band. "1024 and voltage/counts". This may be the ticket. Just a little more guidance on where to make the changes please.
Thanks,
R.S.
ADX item creation
Create the ADX "Value" item on the correct offset (word or channel #) with the conversion numbers below.
The ADPAC external channels for the AutoProm are 10 bit so they use 1024 steps for a zero to 5 volt input signal.
Set the size for 16 bit value.
Use 15.04 AFR span/1024 counts = 0.0146875 +7.35
(Actual typed in box is "X*0.0146875 +7.35"
Gives 0-5 volt range of 7.35 to 22.39:1 AFR
WB controller is set for values of 0-5 volt output = 7.35 to 22.39 AFR
your reading will be correct.
The ADPAC external channels for the AutoProm are 10 bit so they use 1024 steps for a zero to 5 volt input signal.
Set the size for 16 bit value.
Use 15.04 AFR span/1024 counts = 0.0146875 +7.35
(Actual typed in box is "X*0.0146875 +7.35"
Gives 0-5 volt range of 7.35 to 22.39:1 AFR
WB controller is set for values of 0-5 volt output = 7.35 to 22.39 AFR
your reading will be correct.