TunerPro User Forum

daveinet

Have you seen this series:
http://www.handheldoscilloscope.net/tek ... lloscopes/
This is what I use for field service. Several storage modes and programmable presets. Much better than the bulkier units that have all the knobs on them, but don't do much.

daveinet

Never liked the Fluke scopes. They make great meters, but their scope is very lacking. Look at Tektronix for O-scopes.

daveinet

Actually to be able to break out all the tabs to separate windows would be nice. Some things are nicer to see graphically, some are nicer to see in text form, some better in tables. The is another program that allows you to see the BLM table, the item list and the monitor all at the same time.

daveinet

$0E instead of $0D. Had the wrong Mask. Honken sent me a defintion that was closer than what I had, but I later discovered I had the wrong mask. Once I used the correct mask, everything works. It may be a while before i can give a specific answer. My computer blew the hard drive and I have as of yet...

daveinet

Say, anyone ever done a live HP calculation based on fuel flow and RPM? Not that it would be perfectly accurate, but it could be kind of fun to read out HP development in real time.

daveinet

I've had a couple of times where it would be nice to have 2 instances of TunnerPro open at the same time, but it will not allow it. I've done this a few times when I've done this with ScannerPro to fix compare/fix some of the calculations. I've tried to do the same with TunnerPro and it will not let...

daveinet

I guess I should maybe clarify. The engine runs pretty well and is dialed in pretty close. BLMs are all +/- 5, engine idles just fine. We spent nearly a day on it getting it this close. There are just a few things I would like to touch up. These are more planned experiments rather than trying to get...

daveinet

Ok, So I've been thinking about getting an emulator and have started to wonder how practical is an emulator? Although I realize the limits of making test runs and burning chips, I was thinking about getting set up with a EX/GX remote switcher instead. I'm just not sure, since I'm the only one drivin...

daveinet

I think it is the total rate per bank. The ECM has no idea how many injectors there are per bank, it is just thinking about total fuel per bank. That is the way mine is set up. Really to convert to TPI, they will often use the original chip, but then fudging the injector rate to shift the total fuel...

daveinet

Oops, I need to correct my statement. It does not get the errors every so often in the command /reply, but I do get the error log file problem where it does not want to play the log file with out stopping after the first 2 seconds and then having to restart again. When I first installed this on the ...

daveinet

Have you downloaded lately? A similar problem was fixed months ago. Let me know if you see it with a re-download (and a NEW log). Yes, I've been running the latest version and it has the same problem. Could it be something screwy in the definition, or maybe some strange data on the where the def do...

daveinet

Yes, and while we are on log playback, for some reason when ever I play back a log, it plays two replys and then stops. If you pause and restart it, it takes off and runs, but skips the first minute or so of data. Both my XP and my Vista have this problem even on different files recorded on each ind...

daveinet

Thanks for the links. That's tempting for the price. The mouse pad is difficult to use.

daveinet

The mount is a piece of tinted Acrylic bent with a paint stripper heat gun. Just clamp the end, heat it up and fold it over. Cut the mouse slot out with a router. Touch screen would be real nice if I could get a small one. Actually that was the main motive for buying it was the small screen size/sma...

daveinet

Thought I would show off my dash here for fun. I'm really liking this Acer netbook for this application. Its small, and convenient. http://i213.photobucket.com/albums/cc10/Daveinet/Engine/DSC06088.jpg I'm actually running live video at the same time I'm running ScannerPro. The live video is for my b...

daveinet

The problem was with log files created with the previous build being compatible with the most recent build. I've gone back to an old version (I keep one on hand that runs in my WIN98 box) and have been able to run the old logs. The export feature would still be beneficial, so one can inspect details...

daveinet

Is there any way to translate an XDL file to comma delimited? I have some old files I'm trying to play back, but regardless of what definition I use it just crashes. Need to be able to compare old data to the new data.

daveinet

Also would like o know if seeing slightly more vacuum as the RPM goes up is normal, or is my intake too restrictive?

daveinet

I have a two part question regarding data I read under WOT. As the engine RPM increases, there is a slight down hill trend in the O2 reading. I also notice the pulsewidth decreases slightly as the RPM rises. KPA also decreases slightly as well - goes from 98 down to 92 from 2K to 4.8K rpm. Should I ...

daveinet

This is a bit interesting to me. I'm struggling if I should take the plunge to Linux. With the advent of the inexpensive Netbooks, the motivation to move to Linux is quite high - especially with SSD, so that bouncing around in a vehicle doesn't take a chance on damaging it. A nice small package is v...

daveinet

I have a question about the nature data coming across the port. Does the ECM just dump all the data at once based on a single command, or is ScannerPro requesting each individual piece of data that comes across? the reason I am asking, is I am curious if there is a way to increase the resolution of ...

daveinet

I'm using a ECM from a '95 GM truck (#16197427). Does this late of ECM still have economy mode available? If so, does any one know how to enable it? Is there a flag that is set when it is enabled? If so, where?

daveinet

I think we are going to try just removing the catalytic converter routine, but it does seem like it may be worth adding the sensor anyway. In that regard, do you have any idea what the pulses out of the sensor should look like? The reason I ask is because I have an after market cruise control that u...

daveinet

One other clarification. The flag and the rich flat line O2 happen simultaneously. It will maintain that condition for a minute or two and then the flag goes false at the exact same time the O2 begins toggling. So I assume the rich condition is in response to the flag, as opposed to the other way ar...

daveinet

Well, I partially found an answer. I've noticed the converter over temp flag is set at the same time it goes rich, and shuts off when it returns to normal. What i don't know is which converter. Is it the torque converter or the catalytic converter. Unfortunately, the label for the flag does not spec...

daveinet

I'm running computer 16197427 $OD mask. Computer is from a '95 GMC pickup. This has been retrofitted into an older motorhome. I had someone else do the chip. Engine runs well under everyday driving, however once I hit the freeway, after cruising for around 5 minutes or so, the O2 sensor will just go...

daveinet

Just installed the latest version under Vista. Now anytime the program loads, I get "FAILED to Load Error opening file". I have to manually load the most recent definition. Previously this worked fine, just start the program and the definition would automatically load fine, but now it gets...

daveinet

Yes, Honken's worked for me Thanks. Easy enough to fix the temp, just change the conversion to X * 1.350000 + -40.000000 - taken from the original OD from Tuner Pro conversion. Seems to work fine. BTY: I'm guessing both of your problems are related. I know if edit the def and then click save, I also...

daveinet

So how many dashboard items can one cram onto a 15" screen?? I see you going crazy on another post. I'm running a 17" screen, so I need to fill it up. I still want to play around with trying to layer gauges within gauges like pulse width and MAP.

daveinet

The big problem you will have will be trying to find a laptop that is running XP. Vista is the worst piece of junk any software company has come up with. I'm running an Acer with 4 USB ports and cursed with Vista. It is a wide screen with the numerical pad. One thing I like about it is that it has h...

daveinet

What is the difference between running average and history average? From my limited knowledge on tunning, I've read that with the O2 sensor, mostly what one cares about is the fact that it toggles, not particularly how far it toggles. If this is the case, could one put constraints on the read out of...

daveinet

an additional comment on program booting to most recent tab, maybe a better thought would be a command line like ScannerPro.exe/C/D for auto C onnect on start up and open D ash tab. The comment about having a gauge within a gauge is interesting. I actually have overlapped the gauges just to see what...

daveinet

Well, I tried it, but something is not right. It does not ever increment the count. One other weird thing is that the knock retard never shows either. I assume that there is knock on occasion as TTS will show a count as well as show an amount of retard anytime I accelerate.

daveinet

Thanks, I've programed it, hopefully I'll have a chance to see if it works tomorrow.

daveinet

It would be nice if when the program booted, it would boot to the last tab displayed when shut down. When driving, minimizing the number of keystrokes to get to the correct page when driving is important. I have a hot key that boots the program directly, for me, I would always have it come up in das...

daveinet

Does anyone have the packet offset for the knock counter for the 0D mask. This is a 16197427 ECM. Apparently this data is missing from the bin def for TunerPro, which means I can't get this info with ScannerPro either. TTS will give me a knock count, so I assume it exists, but it is missing from the...

TunerPro User Forum

Search found 36 matches

HP calculation

Opening 2 instances of TunnerPro

How practical is an emulator - really?

XDL to comma delimited

O2 sensor interpetation and Pulse width

data rate??

economy mode

O2 flat lines rich at cruise

630 bug under Vista

Histogram average

Boot defaults

Knock count for 0D Mask