TunerPro User Forum

Six_Shooter

Sounds like you may have had the offset incorrect when you programmed the EPROM, and therefore you were in LHM (Limp Home Mode), in which timing is controlled solely by the dizzy and the module found within. Was your CEL (Check Engine Light) on when the timing wouldn't advance? If you were using an ...

Six_Shooter

Check out moates.net

Six_Shooter

Yeah, that was a known problem, there was a solution posted for it back when V4 was still current. Try searching for that on the forum.

Why not switch to V5?

Six_Shooter

Ok, use "Target Save As..." It's been a very long time since I've used IE, so I sometimes forget the nomenclature. No need to pay (me), I needed help in the past to get up and running and still look for help on specific issues now and then. ;) As far as the Moates guide goes, I've never ne...

Six_Shooter

I think you're using Internet Explorer? When you want to download a file from the downloads section, right click and "save as..." This will download it in the correct format. Yes, ADX is the replacement for ADS, because the format was a large departure from from the previous format. The im...

Six_Shooter

Would that price include to Canada? (I'm assuming you're in the US.)

Six_Shooter

Don't worry about the code 59 stuff, that does not apply to at all. He should have mentioned that this was for specific applications. He may have intended to only post it on code 59, or in reply to code 59 topics, without mentioning it the video, which is confusing to people that are new or rusty. W...

Six_Shooter

You are loading the correct XDF, BIN ans ADX for the application(s), correct?

Six_Shooter

Well if we were to plug in an extra mouse with a scroll wheel, the scroll event (up/down) should be able to change the value by the step value. That would be aw3some for dialing things in! I haven't used it personally, but I believe you can use the up and down keys to increase and decrease values o...

Six_Shooter

1. When the data is working, also highlight the cell in the applicable table. ie, RPM/MAP/VE, or Temperature/RPM. This is already possible when data tracing is set-up correctly, and needs to be done as a per table/scaler basis, for set-up. 2. Fix cntl-F so that if the dialog is already up, the curs...

Six_Shooter

If this is the cable you have: http://www.reddevilriver.com/ALDL_Bluetooth.html

Then I believe the only way it will actually transmit data is through Bluetooth, not the USB. I'm not quite sure what the USB connector is for on that, other than possible firmware upgrades.

Six_Shooter

If Mark does add something like this, I hope it's selectable (toggle on/off) and/or adjustable for length of trail. I can see how it could be useful, but it might be distracting at times as well.

Six_Shooter

While emulating the Ostrich takes place of the EEPROM, not the ECU hardware. So the ECU will read values from the EEPROM/Ostrich in order to make calculations while running.

QuarterHorse is a tuning product made and sold by Moates for Ford applcations.

Six_Shooter

Sounds like quite an opportunity cost to me. =) LOL, I would likely have kept one laptop just for Tuner Pro then. :P I really like the way you have made Tuner Pro. I never understood the expiring licences of some other tuning software out there. FWIW, I don't usually have Tuner Pro installed on any...

Six_Shooter

I must be up to a couple dozen registered copies by now over the years, with new PCs/Laptops and re-formats over the years with the same key. lol

Six_Shooter

dfddfd2 wrote:The link for the RT version is:
http://www.tunerpro.net/download/SetupT ... 0_8383.exe

Look at the version number in that link, 8383, not 8414.

This is what I'm talking about.

Check your installed versions, they may be 8383.

Six_Shooter

Download page indicates that the latest version is 8414, but what is downloaded is version 8383.

http://tunerpro.net/downloadApp.htm

Six_Shooter

That should work, but there are a number of good $8D XDFs already available, and for S_AUJP, as well.

Six_Shooter

The conversion pulled from the ADX will not work with the AD conversion of the Arduino. The GM computer is 8 bit, so 256 values, and the raw data is sent in this 8 bit value, that the ADX (and scanners) use the conversion to come up with an actual value. Arduino AD converter is 10 bit, which has 102...

Six_Shooter

If it's stock, it won't be $6E. $6E was 1989. I'm not even sure your '86 would be $32 or $32B, I know those were '87 and '88 for sure, I don't recall what '86 used.

Six_Shooter

It sounds like the chip offsets are incorrect, as in one of the addressed, likely the higher/end address is beyond what the 2732 chip could actually contain.

Six_Shooter

Yes. One registration file works on as many computers as you own. This is good for when a computer needs to be replaced. I also register my copy on my PC so that when I'm reviewing logs and bins on my desktop it makes it gets rid of that nag screen.

Six_Shooter

Yeah, the use of an Ostrich has nothing to do with the data acquisition and the dash. That is entirely to do with the DA and the use of a datalogging cable, such as the ALDL Xtreme from Moates.

Six_Shooter

The XDF is not contained in the ECM, it is a file that is opened by Tuner Pro to "mask" the bin file and make it easy to read by humans.

Have you set the proper com port for the ALDL cable in Tuner Pro RT?

Six_Shooter

Yes, as long as they are both for the same application.

Six_Shooter

Maybe try uninstalling and re-installing Tuner Pro to make sure there isn't a corruption in the install.

Six_Shooter

Have you tried loading the XDF and bins that are packaged with Tuner Pro as part of the program download?

Six_Shooter

I don't know, if you follow the instructions in the link it should work fine. It's as simple as going to "load XDF", browsing to it, clicking on the XDF you want to load to high light it, then clicking open. It's the same for the Bin file and for the ADX. You can, instead of clicking on th...

Six_Shooter

There's no conversion needed to load a bin and xdf file within Tuner Pro.

Maybe list the steps you are using to load the files and we might be able to pick up on what is causing the issue.

Six_Shooter

Have you checked fuel pressure? Have you performed a tune up? Have you cleaned the IAC passage/throttle body? Have you filled up at a different station than usual or different grade of fuel? The O2 sensor is a reactive device, not a controlling device, so stop being so focused on it. Yes, the feed b...

Six_Shooter

In closed loop, that's how the O2 sensor should act.

Six_Shooter

In Chrome:

Right click > Save link as...

Six_Shooter

What browser are you using?

Six_Shooter

You have to solve #2 before #1 will be of concern...

The 1990 Beretta with a 3.1 should use $A1 for code and there are XDFs around for that. You have to load the correct XDF, set the com port in preferences and then you can connect.

Six_Shooter

That's odd. I haven't had any issue copying files over my network, and the files have been as recent as two days ago.

Six_Shooter

Are you simply trying to access the file remotely, or are you trying to copy it over to the PC?

I know in many programs I use, I have to copy a file over to the local PC in order to actually use it.

Six_Shooter

It's not a feature of V5, because people were apparently confused by it.

Change the mask id byte to AA, to disable checksum.

Six_Shooter

1200 may be the lowest setting available. I know I was using a program many moons ago, IIRC it was Scanner Pro, where the lowest setting was the one that worked.

FWIW, Scannerpro, for the most part was integrated with TP RT, with the V5 release, so the same thing should apply here.

Six_Shooter

Sorry, I was thinking xdl files.

There is no import function for your xml file to xdf. If you had an ecu file that could be imported.

You will have to find out where the parameters are in the bin and build an xdf file from that.

Six_Shooter

You need to know where items are in the bin file and several other parameters in order to create an xdf file.

Six_Shooter

MrMike98 wrote:http://forum.tunerpro.net/viewforum.php?f=4
i hope that works

the first 2 sticky's will get u going..
Mike

Making a dash won't help without also having an Autoprom (AKA APU1) to use those instructions. He has the Xtreme ALDL, AKA ALDU1,

Six_Shooter

That's because AFR is not an actual data output item, through the ALDL on that and many, if not all of the OBD1 GM ECMs. In stock ECM form, any "AFR" display would be a guess based on narrow band O2 sensor voltages that are more closer to that of a switch, than a scale-able output. There m...

Six_Shooter

I haven't connected via BT in years, there always seemed to a longer delay for upload verification that seemed to cause more errors than when using a USB cable. I quickly tried a few weeks ago to connect via BT, but didn't give it much effort, I think there was a setting change that I'm forgetting a...

Six_Shooter

Thank you, that's exactly what I needed to change.

Six_Shooter

Is it possible to set TP RT V5 so that when a parameter is closed the tree doesn't jump to the last open parameter? There are times when I'm changing or at least looking at related parameters, say scalers, but then close an open scaler and the parameter tree jumps to the last open parameter, say a t...

Six_Shooter

I wonder if there's another program associated with xdf files that is causing a conflict.

Six_Shooter

Split BLM at idle might get better playing with IAC air flow. distribution issues seem to play a big role in that. http://www.thirdgen.org/techboard/diy-prom/356830-miniram-split-blms.html Also read "Vern's tale on post #8. Idle stink can get better by lowering the o2 constants by small amount...

Six_Shooter

IIRC, the PCM you are using is a flash type PCM, meaning it gets a new calibration flashed through the ALDL connector, and no way of actually emulating, unless you use a Road Runner from Moates. Providing a PCM service number would help clear up any mystery. After you uncheck the VATS boxes, did you...

Six_Shooter

How did you get them to show in Win7? I haven't had them work for a while.

Six_Shooter

Did you set the switch on the AutoProm to "AutoProm mode" as opposed to "pass through mode"?

TunerPro User Forum

Search found 590 matches

Re: Collection of UI improvements

Problem with application download.

Parameter tree jumps