I need help with the bin file
Moderators: robertisaar, dex
-
- Posts: 5
- Joined: Thu Jun 25, 2009 6:37 am
I need help with the bin file
So this has been a semi frustrating deal. I have a tpi setup from a 1989 Firebird that I have put into my 70 Camaro. I have changed a few things on it and it needs help running. It runs to rich. I purchased the emulation device from Moates quite some time ago. I have never really been able to get it to work correctly. I have downloaded different bin files and none seem to be close enough to get it to work. I have gotten the car to run but very poorly. I spoke with Moates and they said that I needed the adapter to pull the bin file out of my stock chip. I have tried doing this but am having a difficult time with it. When I do it is says it was successful but when I go to save it and open it in tunerpro it does not seem to work. Any help would be appreciated.
-
- Author of Defs
- Posts: 962
- Joined: Sat Feb 21, 2009 3:18 pm
- Location: Camden, MI
-
- Posts: 5
- Joined: Thu Jun 25, 2009 6:37 am
-
- Author of Defs
- Posts: 962
- Joined: Sat Feb 21, 2009 3:18 pm
- Location: Camden, MI
-
- Posts: 5
- Joined: Thu Jun 25, 2009 6:37 am
Well I have the file uploaded into the emulator now. I looked it over and the numbers look to be pretty good. All of the other files I would get were way off of what they should be. I still can't get the vehicle to run however. I have started it on the stock chip and then when I hook up the emulator it gives a little fire and then will not do anything after that unless I run it on the stock chip after which it does the same thing. I really need to get this thing figured out.
-
- Author of Defs
- Posts: 962
- Joined: Sat Feb 21, 2009 3:18 pm
- Location: Camden, MI
- Six_Shooter
- Posts: 590
- Joined: Sun May 06, 2007 7:32 am
Could it be that all the ones that "seemed way off" were actually correct, and you're either not seeing numbers that you want or using the wrong XDF so that the numbers will be skewed or jumbled? I've done that a few times myself. lol
Are you using a $32B XDF? The info I have shows that BCC is for an '88 using a '165 ECM, which IIRC is $32B code mask.
The bins should be 16Kb in size.
Are you using a $32B XDF? The info I have shows that BCC is for an '88 using a '165 ECM, which IIRC is $32B code mask.
The bins should be 16Kb in size.
-
- Posts: 5
- Joined: Thu Jun 25, 2009 6:37 am
I checked the Vats and there is no check mark in the box.
I am running that 32b xdf file. The problem with the figures I was getting before was that the numbers would look semi plausible and then one of the numbers in the map would be ten times what everything else was.
I am wondering if somehow the emulator is just not working right.
I am running that 32b xdf file. The problem with the figures I was getting before was that the numbers would look semi plausible and then one of the numbers in the map would be ten times what everything else was.
I am wondering if somehow the emulator is just not working right.
hugger70camaro wrote:I checked the Vats and there is no check mark in the box.
I am running that 32b xdf file. The problem with the figures I was getting before was that the numbers would look semi plausible and then one of the numbers in the map would be ten times what everything else was.
I am wondering if somehow the emulator is just not working right.
I'm having similar problems. How did you resolve your poor running condition if you ever did?