Bluetooth on Ostrich V2
Moderators: Mangus, robertisaar, dex
Bluetooth on Ostrich V2
I install a bluetooth module to ostrich V2 emulator.
how can I connect it with tunerpro software?
Bluetooth stay com port
like com12 or com5
this is a virtual serial port
tunerpro no any com port adjustment
its give "no emulator found" error
*Tunerpro working with usb cable ofcourse.
->edit for wrong grammar.
how can I connect it with tunerpro software?
Bluetooth stay com port
like com12 or com5
this is a virtual serial port
tunerpro no any com port adjustment
its give "no emulator found" error
*Tunerpro working with usb cable ofcourse.
->edit for wrong grammar.
Last edited by maxim on Wed Feb 05, 2014 8:43 am, edited 1 time in total.
- Six_Shooter
- Posts: 590
- Joined: Sun May 06, 2007 7:32 am
I haven't connected via BT in years, there always seemed to a longer delay for upload verification that seemed to cause more errors than when using a USB cable. I quickly tried a few weeks ago to connect via BT, but didn't give it much effort, I think there was a setting change that I'm forgetting about to enable it.
The Tablet and portable question has been asked and suggested for years, according to Mark, it's just not going to happen, at least for anything other than a full Windoze based OS. A tablet running Win8 should be able to run TP, but I have not tried it myself to confirm that.
The Tablet and portable question has been asked and suggested for years, according to Mark, it's just not going to happen, at least for anything other than a full Windoze based OS. A tablet running Win8 should be able to run TP, but I have not tried it myself to confirm that.
I try again connect with bluetooth.
please could you someone tell me what is the serial port baudrate?
when tunerpro connect ostrich v2 with usb what is the baudrate?
(osctrich use FT232RL usb to serial connection chip)
Im try over bluetooth 9600 and 38400 bps
no connection
tunerpro check hardware and didnt connect to bluetooth module
bluetooth port com10
I can change bluetooth speed
please could you someone tell me what is the serial port baudrate?
when tunerpro connect ostrich v2 with usb what is the baudrate?
(osctrich use FT232RL usb to serial connection chip)
Im try over bluetooth 9600 and 38400 bps
no connection
tunerpro check hardware and didnt connect to bluetooth module
bluetooth port com10
I can change bluetooth speed
For my own AutoProm, which functions essentially the same as the Ostrich, I exclusively use Bluetooth, so I know it works. I believe the module I use is from BlueRadios (the ones Moates used to sell a few years back).
I have not tried Bluetooth with the Ostrich.
Edit: Just chatted with Moates. He said Bluetooth works with the Ostrich. He recommends a Elechouse module.
I have not tried Bluetooth with the Ostrich.
Edit: Just chatted with Moates. He said Bluetooth works with the Ostrich. He recommends a Elechouse module.
***************************************
TunerPro Author
1989 Trans Am
TunerPro Author
1989 Trans Am
-
- Posts: 4
- Joined: Sat Jan 04, 2014 12:56 pm
bluetooth
I would also like to know. Also in the first picture, are the pin outs correct?
Craig says this one should work:
http://www.elechouse.com/elechouse/inde ... 03rlfq0qt5
Note that you'll likely have to configure it, so you'll need the appropriate hardware (USB/TTL) to send it the proper AT commands to do so. I don't have experience with it myself, so I won't be of much help.
http://www.elechouse.com/elechouse/inde ... 03rlfq0qt5
Note that you'll likely have to configure it, so you'll need the appropriate hardware (USB/TTL) to send it the proper AT commands to do so. I don't have experience with it myself, so I won't be of much help.
***************************************
TunerPro Author
1989 Trans Am
TunerPro Author
1989 Trans Am