TunerPro User Forum

Thanks for the response, I'll contact and see what else can be done.

Thanks for your feedback. I honestly don't know what to say because I was told it was tuned for an M20, with a setup like mine, m20 2.5 running on M50 management system. What would you do to help for it to be M20 compliant?
I really appreciate.
Thanks.

Thanks. Here are the links posted to Mega. Let me know if they work.

https://mega.nz/#!NDh1HSoR!PqwFpI_Kle_Y ... nW-i1RHHsk
https://mega.nz/#!RHJQWAIS!agxteE15dynt ... VgM5ZsF0Po

Hmm! I'll try to put m20 injectors and see how it will behave. I'll update what I find

I am using a 405 ecu.

Nobody has some insight??

That's the conclusion I had reached as well. M50 injector is ~190cc/min at 3.5 bar from what I can see. My injector voltage correction is: Volts - 7.8 - 9.8 - 11.7 - 13.7 - 15.7 M20 - 2.55- 2.14- 1.55 - 0.98 - 0.52 M50 - 2.10- 1.80- 0.72 - 0.56 - 0.36 Big difference in the response curves and massi...

I haven't adjusted the Injector constant values, and I will look at exactly which M50 MAF I am using.

Hairyscreech wrote:I can't open either of your pictures, the link just 404s

Try if they are opening now.

Ok, on Tunerpro RT what is the injector constant of each, m20 17lbs and m50 19lbs? Does this look right for any of these injectors?

https://goo.gl/photos/32RLxTnnHvKvGv2RA

Does this MAF table looking right too for the m20?

https://goo.gl/photos/eKRVUGfQAj6gqscq8

How do you set up the ECU to the correct injector latency and fueling.

So, for an M20 Engine with M50 management, which injectors are best to use, m20 17lbs or m50 19lbs?

What is injector constant for m20 stock injectors (17lbs), and how do you calculate it?

I am not using any wide band at the moment, just stock. For the TPS I am using an adapter that was being sold on the e30 forum that can attach the m50 TPS, but you will need to rotate the throttle body shaft 180, and switch the throttle body wire plugs pins 1 and 2. to orient it the same as the M20 ...

Yes, I have tunerpro RT, I am sure the TPS and the CPS are good. I have tested them on an M50 and they are fine. Looking at the stock bin and xdf on tunerpro, there are a lot of tables and scalars. But the tune I am using has been scaled down to a few tables and so it can be used with an m50 xdf, th...

If you have an ostrich you can trace the tables and adjust fueling and spark with Tunerpro. Are you using m50 sensors? Specially the cam position sensor? What idle valve are you using? Do you use the maf from the m50? If not, you're running in alpha n mode and thé tables are surely not adapted for...

Yes, am running m50 sesnsors, cam position sensor, MAF, TPS, and idle control valve, but using the m20 throttle body housing sesnsors (Blue and brown Temp Sensors). The vehicle runs and drives but very rich and poor idle.

can you give more explanation ? what exactly are you doing ? I am currently running m20 using an M50 NV ignition system and wiring harness with coil on plugs. I am using an e36 ECU piggy backed to Moates Ostrich 2.0 with the tune am using. But it is running very rich with a very erratic idle. Let m...

Do we have anyone who can clean up a tune I have to accommodate with the right parameters for an m20 325i, which using an ignition system with coil on plugs. It has an e36 ECU piggy backed to Moates Ostrich 2.0 with the tune. I have the right xdf and bin. Modifications on the m20 are E36 TPS, CPS an...

gath wrote:How do I load a tune from Ostrich 2.0 in my car on to Tunerpro on my computer?

Figured it out

How do I load a tune from Ostrich 2.0 in my car on to Tunerpro on my computer?

Thanks Mangus, that seems to work.

Dang! Yes, I just realized that I was using a 402 xdf instead of a 403. Now I have encountered another problem, I have the right 403 bin but the program wont open the 403 xdf because it says that the "attributes need to be enclosed by quotes marks". How do I go changing the attributes to h...

I am noobie to tuning and I have two bins for the same dme but the tables in the parameter tree are different as noted in the pics. How do i get them to be the same and have the same values? http://i1283.photobucket.com/albums/a548/xepa1/Capture2_zpsdb30aa5b.jpg http://i1283.photobucket.com/albums/a...

Made some progress but I have a question. How do I advance timing in bmw m20 engine with m50 management. I need to advance timing by about 20 degrees, which maps do I tweak and how do I go about it? am using a 403 ecu. Thanks.

Thnx, I'll update progress.

'am back on this project and I think I might have made some progress on it. The xdf file that I had been sent is not being read by tunerpro (maybe it is corrupted), so I downloaded an xdf file for the same ecu on this site and used it to open the bin file sent to me with the unopenable xdf file just...

Hi, thnx, I reinstalled the program and now I can open the definitions from the tunerpro site but not the one I was sent. The one I was sent 32kb and the tunerpro file 16kb have the same properties - XDF File (.xdf), but when I try to opening it say the "attribute values must be enclosed in quo...

Well, i guess I have a bigger problem because am unable to load even the file from tunerpro. This is sad, I think I'll go through the whole tutorial which 'ave done over n over, I still don't see where am going wrong.

I don't know, if you follow the instructions in the link it should work fine. It's as simple as going to "load XDF", browsing to it, clicking on the XDF you want to load to high light it, then clicking open. It's the same for the Bin file and for the ADX. You can, instead of clicking on t...

I have downloaded the bin n xdf files into a folder on the comp. I go to the select xdf file in the tunerpro and select the xdf from the folder but it doesn't load. No parameter option are selectable when I go to the parameter tree, what am I doing wrong? am even trying to follow this but still noth...

Hi, i have a bin and a xdf file I was sent in the email for my setup but am unable to load it in the tunerpro rt. I have a binary viewer in my computer, I can load and view the files there but not in the tunerpro, I have tried following all the steps that are shown but still in vain. What other prog...